Open Access Journal

ISSN : 2394-2320 (Online)

International Journal of Engineering Research in Computer Science and Engineering (IJERCSE)

Monthly Journal for Computer Science and Engineering

Open Access Journal

International Journal of Engineering Research in Computer Science and Engineering (IJERCSE)

Monthly Journal for Computer Science and Engineering

ISSN : 2394-2320 (Online)

Review on Aluminium Conductors

Author : Kumar Sambhav 1

Date of Publication :20th November 2017

Abstract: The interest of power is consistently expanding and gives a high weight on the current transmission arrange. With the current conductor, there will be more misfortunes happen in “All Aluminium Alloy Conductor (AAAC)”, contrasted with “All Aluminium Conductor (AAC)”. To beat this issue, conductor as transmission line with ability to lead more current is required. Aluminium is a decent present conductor; low in cost and lighter weight contrast with copper. These points of interest improve the use of aluminium conductor as overhead line of transmission system. However, the shortcoming is on mechanical part, which isn't reasonable to encompassing condition. This paper centers on the components that impact the conductivity and current conveying limit of aluminium conductor. From the metallographic and Transmission Electron Microscope (TEM) examination, it will show the motivation behind why the conductivity property of “All Aluminium Alloy Conductor” is higher than “All Aluminium Conductor”. Some exploratory outcomes that confirm the hypothetical qualities are exhibited. The exhaustion conduct between an All-Aluminium Alloy Conductor (AAAC) and an “Aluminium Conductor Steel Reinforced (ACSR)”. These links use Aluminium Alloys (AA) 6201-T81 and 1350-H19, individually. This test program was completed at a resounding fussing exhaustion seat for overhead conductors at the University of Brasília. The outcomes indicated that the “Aluminium Conductor Steel Reinforced”. conductor flops by weariness when is exposed to bowing sufficiency feelings of anxiety which are in normal more than 1.25 occasions more noteworthy than that continued by “All Aluminium Alloy Conductor” conductors (for the existence ranges considered)

Reference :

    1. “Non-ferrous metals,” in Materials Science in Construction: An Introduction, 2014.
    2. R. Ditz, “Separation technologies 2030 - Are 100 years of chromatography enough?,” Chemie-Ingenieur-Technik, vol. 84, no. 6. pp. 875–879, 2012
    3. R. B. Kalombo, J. M. G. Martínez, J. L. A. Ferreira, C. R. M. Da Silva, and J. A. Araújo, “Comparative Fatigue Resistance of Overhead Conductors Made of Aluminium and Aluminium Alloy: Tests and Analysis,” in Procedia Engineering, 2015.
    4. V. K. Sood, “HVDC transmission,” in Power Electronics Handbook, 2011.
    5. D. Subcommittee, “IEEE Guide for Electric Power Distribution Reliability Indices,” Distribution, 2012.
    6. L. Keviczky, R. Bars, J. Hetthéssy, and C. Bányász, “Introduction to MATLAB,” Advanced Textbooks in Control and Signal Processing. 2019.
    7. Microchemicals, “Aluminium Etching (Al),” Microchemicals, p. 2013, 2013.
    8. R. B. Kalombo, J. A. Araújo, J. L. A. Ferreira, C. R. M. da Silva, R. Alencar, and A. R. Capra, “Assessment of the fatigue failure of an All Aluminium Alloy Cable (AAAC) for a 230 kV transmission line in the Center-West of Brazil,” Eng. Fail. Anal., 2016.
    9. A. A. Fadel, D. Rosa, L. B. Murça, J. L. A. Fereira, and J. A. Araújo, “Effect of high mean tensile stress on the fretting fatigue life of an Ibis steel reinforced aluminium conductor,” Int. J. Fatigue, vol. 42, pp. 24–34, 2012.
    10. T. Fuhrmann et al., “Development, research and qualification of new aluminum alloys for current-carrying joints,” VDE Fachberichte, 2017.
    11. C. S. Goh, M. Gupta, A. E. W. Jarfors, M. J. Tan, and J. Wei, “Magnesium and Aluminium carbon nanotube composites,” Key Eng. Mater., vol. 425, pp. 245–261, 2010.
    12. S. D. Jadhav, S. Dadbakhsh, L. Goossens, J. P. Kruth, J. Van Humbeeck, and K. Vanmeensel, “Influence of selective laser melting process parameters on texture evolution in pure copper,” J. Mater. Process. Technol., 2019.
    13. Nisha Pandey, B. S. Chowdhary , Bhagwan Das , D. M. Akbar Husain , Vishal Jain , Tanesh Kumar, “Design of Data Processing Device on Low Power SPARTAN6 FPGA”, International Journal of Control and Automation (IJCA).
    14. Sujeet Pandey, Puneet Tomar, Lubna Luxmi Dhirani, D. M. Akbar Hussain, Vishal Jain, Nisha Pandey, “Design of Energy Efficient Sinusoidal PWM Waveform Generator on FPGA”, International Journal of Signal Processing, Image Processing and Pattern Recognition (IJSIP), Vol. 10 No. 10, October, 2017, page no. 49-58 having ISSN No. 2005- 4254.

Recent Article